Field Reference

Lap Joint Flange: What It Is and When It Is Used

November 2026By Vini P.K.
lap-joint-flange-assembly

Short Answer

A lap joint flange is a loose backing flange that slides over a stub end and is never welded to the pipe. The stub end is butt welded to the pipe and carries the sealing face, while the flange only clamps it to the mating flange with the bolts. Because the flange can turn, its bolt holes line up easily, and because it never touches the fluid, it can be carbon steel on a stainless or alloy line.

Works with
A stub end, butt welded to the pipe
Flange standard
ASME B16.5
Stub end standards
ASME B16.9 long pattern, MSS SP-43 short pattern
Also called
Lapped joint flange, Van Stone flange

Field Reference · Flanges

Lap Joint vs Slip-On vs Weld Neck Flange

How a lap joint flange compares with the two flanges it is most often mistaken for or swapped with.

Lap JointSlip-OnWeld Neck
How it attachesRides loose on a stub end, with no weld to the flangeSlides over the pipe, with two fillet weldsButt welded to the pipe
Sealing faceOn the stub endOn the flangeOn the flange
Turns after installYesNoNo
ServiceModerate, with lower fatigue lifeLow to moderateSevere, including high pressure and cyclic service
Welds per jointOne butt weld, stub end to pipeTwo fillet weldsOne butt weld
Best forAlloy lines, frequent dismantling, bolt hole alignmentLow pressure lines and easy fit-upHigh pressure and high temperature lines

Flange dimensions are set in ASME B16.5. Bolt counts and sizes by class are in the flange bolt chart.

What Is a Lap Joint Flange?

A lap joint flange looks like a slip-on flange with a rounded edge on the back of the bore. That radius lets it sit snugly behind the lap of a stub end, which is a short length of pipe with a flared face on one end. The stub end is butt welded to the pipe, and the flange goes on before the weld is made so it can be slid up against the lap.

When the joint is bolted up, the gasket seals between the stub end face and the mating flange. The lap joint flange only supplies the clamping force, so it sees no fluid and needs no raised face. ASME (American Society of Mechanical Engineers) B16.5 sets its dimensions alongside the other common pipe flanges.

Stub Ends and Van Stone Flanges

Stub ends come in two lengths. Long pattern stub ends follow ASME B16.9, and short pattern stub ends follow MSS SP-43 from the Manufacturers Standardization Society. Short pattern pieces are common on stainless steel lines, where a shorter piece saves alloy.

Van Stone flange is an older name for the same idea. It first described a pipe end flared over in the shop with a loose flange behind it, and in the field it is still used for a lap joint flange and stub end set.

When a Lap Joint Flange Is Used

  • Stainless steel, alloy or lined pipe, where a carbon steel backing flange saves money because only the stub end touches the fluid
  • Lines that are taken apart often for cleaning or inspection
  • Hookups to equipment nozzles, where turning the flange lines up the bolt holes
  • Plastic and HDPE (high-density polyethylene) pipe, where a backing ring bolts up behind a fused flange adapter

The trade-off is strength. A lap joint has a much lower fatigue life than a weld neck flange, so it is kept out of high pressure, high temperature and cyclic service, where the specification normally calls for weld neck.

Lap Joint Flange vs Slip-On Flange

The two look alike on a pipe rack and can share a similar symbol on a drawing, so check the pipe class sheet. A slip-on flange is fillet welded to the pipe inside and outside, and its bore matches the pipe. A lap joint flange is never welded, its bore is a little larger with a radius at the back, and it is always paired with a stub end.

What to Count for Each Lap Joint Flange

  1. The lap joint flange, by size, pressure class and material
  2. The stub end, by size, schedule, pattern and material, which usually matches the pipe
  3. The gasket for the mating joint
  4. One set of stud bolts and nuts, by class and size
  5. The butt weld between the stub end and the pipe, counted in diameter inches for labor
  6. The bolt-up of the flanged joint

The usual miss is counting the flange and forgetting the stub end, or pricing the stub end in carbon steel when the line is stainless. Each lap joint is two pieces of material, and the stub end carries the line's material grade.

How The Takeoff AI Handles Flanged Joints

The Takeoff AI reads the piping and instrumentation diagrams (P&IDs), isometrics and plans and takes off the piping end to end. It counts every flange, stub end, gasket, bolt set, valve and fitting, counts the welds and measures every length, then prices the material takeoff (MTO) and labor takeoff (LTO) into a priced bill of materials (BOM) at your own rates.

It is trained on more than 1 million drawing sets, runs at 95% accuracy, and highlights every quantity on the sheet it came from, so the estimator can check each flanged joint before the bid goes out. 113 estimators say The Takeoff AI is the best piping estimating software they have used, and it helps them estimate projects in 3 to 4 hours that once took 40 to 50 hours.

Before You Ask

Frequently Asked Questions

Short answers on lap joint flanges, stub ends and how they get counted.

What is a lap joint flange?

A loose flange that slides over a stub end and clamps it to the mating flange. It is not welded to the pipe.

What is a stub end?

A short piece of pipe with a flared lap on one end. It is butt welded to the pipe and forms the sealing face of a lap joint.

What is the difference between a lap joint flange and a slip-on flange?

A slip-on flange is fillet welded to the pipe. A lap joint flange rides loose on a stub end and is never welded.

Is a Van Stone flange the same as a lap joint flange?

In the field, yes. Van Stone is an older name for a loose flange over a lapped pipe end.

Why use a lap joint flange?

To use a cheaper carbon steel flange on an alloy line, to line up bolt holes easily, or on joints that are taken apart often.

Ready when the drawings land

Price your bid before your competitors open the package.

Book a Demo