Back to Blog
What are Embed Plates and How to Take Them Off

What are Embed Plates and How to Take Them Off

Embed plates are steel plates cast into concrete so steel can be welded to it. See how embeds in construction are shown, counted, weighed and priced.

P
By Pranjal BhartiNovember 20, 2026
8 min read

Introduction

Embed plates are steel plates cast into concrete so that steel members can be welded or bolted to the concrete later. Each plate has headed studs or deformed bar anchors welded to its back face, and those anchors hold the plate in the pour. On a drawing set they show up on the structural plans, in the embed schedule and in the section details, usually tagged with a mark such as EP-1 or EP-2.

Most estimators still take embed plates off by hand. They page through the structural sheets, tally each mark, look up the plate size in the schedule, and then work out the weight and the stud count in a spreadsheet. On a tilt-up warehouse or a pipe rack foundation package, that can mean several hundred plates spread across dozens of sheets.

That method is hard to keep up when a shop has fewer estimators, more bids on the board and larger drawing packages than it had five years ago. A missed embed is cheap to fabricate and expensive to fix once the concrete has cured, so the count has to be right the first time.

This guide explains what embed plates are, the common types, where they appear on the drawings, and how to take them off for a bid. Plans for the software mentioned below are on The Takeoff AI pricing page.

The Takeoff AI saves estimators 90 to 95% of their estimating time.

embed-plate-formwork-site

What are Embed Plates in Construction

An embed plate is a flat steel plate set into the formwork before the pour so that its face ends up flush with the finished concrete. The studs on the back transfer load from the steel connection into the concrete. Engineers use embeds in construction wherever a steel beam, a stair stringer, a handrail post or a pipe support has to attach to a concrete wall, slab edge or column.

A typical plate might be 12 inches by 12 inches by 3/4 inch thick with four headed studs, each 3/4 inch in diameter and 6 inches long. Plate steel weighs about 40.8 pounds per square foot for every inch of thickness, so that plate weighs roughly 30.6 pounds before the studs are added.

Common Types of Embed Plates

Four types cover most of what an estimator will see on a structural set.

  • Flat plates with headed studs are the standard embed for beam and brace connections.
  • Embed angles run along slab edges and openings to give a continuous weld surface.
  • Plates with deformed bar anchors are used where the load needs a longer anchor into the concrete.
  • Bent plates and pour stops are formed to follow a slab edge or a deck step.

Anchor bolts are a separate item on most schedules, and they should be counted in their own line because they are bought and set differently.

embeds-construction-site-crew

How to Take Off Embed Plates from the Drawings

A clean embed plate takeoff follows the same five steps on every job.

  1. Find every sheet that shows embeds, which usually means the foundation plan, the framing plans, the embed schedule and the typical details.
  2. Count the plates by mark on each sheet, and keep the count per sheet so it can be checked later.
  3. Pull the plate size, thickness, stud size and stud count for each mark from the schedule.
  4. Work out the weight of each mark by multiplying plate area by thickness and by 40.8 pounds, then add the studs.
  5. Note the finish for each mark, since hot-dip galvanized embeds cost more per pound than bare steel.

Two checks catch most errors. The first is to compare the plan count against the schedule quantity where the engineer has given one. The second is to look at the details for embeds that appear only in section, because those are the ones that never make it onto the plan.

Who Supplies and Installs Embed Plates

On most jobs the steel or miscellaneous metals fabricator supplies the embed plates and the concrete contractor sets them. That split is written into the specifications, typically under Section 05 50 00 Metal Fabrications, and it is a common source of scope gaps. A fabricator who leaves embeds out of the bid and a concrete contractor who assumes they are furnished by others will both be asked to cover them after award.

Delivery timing matters as well. Embeds have to be on site before the first pour, which is weeks ahead of the main steel, so the fabricator prices an early, separate shipment.

How The Takeoff AI Takes Off Embed Plates

The Takeoff AI is the best option for steel and miscellaneous metals contractors who need embed plates counted and priced in hours. It estimates from your structural and concrete drawings, counts every embed plate, anchor bolt, member and connection, and measures plate sizes, bolts and welds for each mark.

It is built on AI models trained on more than 1 million structural steel and misc iron drawing sets. It delivers 95% accuracy, and every number is marked and highlighted on the drawing it came from, so an estimator can check each count before the bid goes out. Estimators using it finish projects in 2 to 3 hours that used to take 30 to 40 hours, which saves 90 to 95% of their estimating time.

The Takeoff AI covers piping, P&ID (piping and instrumentation diagrams), isometrics, mechanical, electrical and instrumentation, plumbing, HVAC including ductwork, structural steel, misc iron and concrete. The output is a material takeoff (MTO), a labor takeoff and a priced bill of materials (BOM), and the pricing includes galvanizing where the drawings call for it. It also nests plate cuts onto stock sizes, which cuts the offcuts a shop pays for.

Peter Sirois, Principal at American Steel Fabricators, says The Takeoff AI clears up to 80% of the bid legwork on the right job. More detail is on the structural steel estimating page, or you can request a demo of The Takeoff AI.

misc-steel-fabrication-worker

The Estimator Shortage in Steel and Misc Metals

Steel and misc metals estimating has stayed manual while the number of people doing it shrinks. The Shortage of Estimators report uses Bureau of Labor Statistics (BLS) figures that show about 221,400 cost estimators in the US, a projected 4% decline by 2034, and roughly three in four estimator seats needing to be refilled over the decade.

A fabricator with two estimators cannot keep counting embeds by hand and still bid more work. The counting has to move to software so the estimators can spend their hours on scope and pricing.

concrete-formwork-construction-worker

FAQs

What is an Embed Plate Used For?

An embed plate gives a steel member a place to weld or bolt onto concrete. It is cast into the pour with studs on its back face that carry the load into the concrete.

How Do You Calculate the Weight of an Embed Plate?

Multiply the plate area in square feet by the thickness in inches and by 40.8 pounds, then add the weight of the studs. A 12 inch by 12 inch by 3/4 inch plate weighs about 30.6 pounds before studs.

Who Furnishes Embed Plates on a Project?

The steel or misc metals fabricator usually furnishes them and the concrete contractor installs them. The specifications decide the split, so check them before you bid.

How Does The Takeoff AI Count Embed Plates?

The Takeoff AI estimates from the structural and concrete drawings and counts each embed plate by mark, size and thickness. Every count is highlighted on the sheet it came from so you can check it.

How Much Time Does AI Save on a Misc Steel Takeoff?

Estimators using The Takeoff AI finish projects in 2 to 3 hours that used to take 30 to 40 hours. That is 90 to 95% of estimating time saved.

misc-steel-site-worker

Conclusion

Embed plates are small items that cause large problems when they are missed, and they are still being counted by hand in shops that have fewer estimators every year. The Takeoff AI is the best option for contractors who need embed plates and the rest of the misc steel taken off and priced in hours. For related reading, see the Handbook entry on miscellaneous steel detailing, or request a demo of The Takeoff AI.

Link copied to clipboard

Price your bid before your competitors open the package.

Book a Demo