Field Reference

Blind Flange: What It Is and How to Take One Off

November 2026By Vini P.K.
blind-flange-3d-viewBLIND FLANGEWELD NECK FLANGEGASKETPIPECOUNTEDBLIND FLANGE1GASKET1STUD BOLTS8NUTS16

Short Answer

A blind flange is a solid flange with bolt holes and no bore, bolted to the end of a pipe, valve or nozzle to close it off. It seals against the mating flange with a gasket, so each one comes with a gasket and a set of stud bolts and nuts. On a takeoff, a blind flange is counted by size, pressure class, facing and material, along with that gasket and bolt set.

Standard
ASME B16.5, up to 24 inch
Facings
Raised face, flat face or ring type joint
Comes with
A gasket and one set of stud bolts and nuts
Common materials
Carbon steel and stainless steel
Field Reference · Piping

Blind Flange Chart: Class 150

Outside diameter and bolting for each blind flange Class 150 size, ASME B16.5, raised face.

NPS (in)Flange OD (in)BoltsBolt Size (in)
1/23.5041/2
3/43.8841/2
14.2541/2
1-1/25.0041/2
26.0045/8
37.5045/8
49.0085/8
611.0083/4
813.5083/4
1016.00127/8
1219.00127/8

NPS is nominal pipe size and OD is outside diameter. Confirm dimensions against ASME B16.5 before ordering, and see the flange bolt chart for other pressure classes.

What Is a Blind Flange?

What is a blind flange? It is the flange that closes a line. Blind flanges cap the end of a pipe run, close off a spare valve or equipment nozzle, and seal a line for pressure testing. Because the whole face holds the line pressure, a blind flange is solid all the way across, which makes it one of the heaviest flanges of its size and class.

Carbon steel blind flanges are the most common on process piping, and a stainless steel blind flange is used where the line is stainless. Blind flanges follow the same ASME (American Society of Mechanical Engineers) B16.5 dimensions as the other common pipe flanges, so an ASME B16.5 blind flange in Class 150 bolts straight onto a Class 150 weld neck or slip-on flange of the same size.

Blind Flange Types

TypeWhat It IsWhere It Is Used
Raised face blind flangeA raised sealing ring on the face, the most common facingGeneral process piping
RTJ blind flangeA groove for a metal ring gasket (ring type joint)High pressure and high temperature lines
Tapped blind flangeA blind with a threaded hole in the centerVents, drains and instrument connections
Spectacle blindTwo discs joined by a web, one solid and one open, also called a figure 8 blindLines that are isolated and reopened often
Paddle blind flangeA single solid disc with a handle, also called a skillet blindTemporary isolation between two flanges
Line blindA general name for any blind fitted between flanges to isolate a lineMaintenance and turnarounds

A spectacle blind flange is counted as one piece even though it has two discs, and it sits between two flanges rather than on the end of one.

How to Calculate Blind Flange Weight

Weight (lb) ≈ 0.2836 × π ÷ 4 × OD² × thickness (OD and thickness in inches)

The 0.2836 is the weight of carbon steel in pounds per cubic inch. The result is a little high because it ignores the bolt holes, which is fine for a freight or handling estimate.

Worked Example: A 6 Inch Class 150 Blind Flange

  1. Take the OD from the chart: 11.00 inches
  2. Use the thickness from ASME B16.5 for that size and class, about 1 inch in this example
  3. Area = π ÷ 4 × 11.00² = 95.0 square inches
  4. Weight ≈ 0.2836 × 95.0 × 1.0 = about 27 lb before bolt holes

What to Count for Each Blind Flange

  1. The blind flange, by size, pressure class, facing and material
  2. One gasket to match the facing, such as a spiral wound gasket for raised face or a metal ring for RTJ
  3. One set of stud bolts and nuts, using the bolt count and size for that class
  4. The bolt-up labor for the joint
  5. Any plug, valve or fitting on a tapped blind
  6. For spectacle and paddle blinds, the second gasket and longer bolts needed to fit the blind between two flanges

Common Mistakes on a Blind Flange Takeoff

  • Counting the blind and missing its gasket and bolt set
  • Pricing every blind as carbon steel when the pipe class calls for stainless
  • Missing the blinds used only for hydrotest, which often sit on test packages instead of the isometrics
  • Counting a spectacle blind as two pieces
  • Using Class 150 bolting on a Class 300 joint, which takes more and larger bolts

How The Takeoff AI Handles Blind Flanges

The Takeoff AI estimates the piping and instrumentation diagrams (P&IDs), isometrics and plans and takes off the piping end to end. It counts every blind flange, gasket, bolt set, valve and fitting, counts the welds and measures every length, then prices the material takeoff (MTO) and labor takeoff (LTO) into a priced bill of materials (BOM) at your own rates.

It is trained on more than 1 million drawing sets, runs at 95% accuracy, and highlights every quantity on the sheet it came from. 113 estimators say The Takeoff AI is the best piping estimating software they have used, and it helps them estimate projects in 3 to 4 hours that once took 40 to 50 hours. See it on the piping page.

Before you ask

Frequently Asked Questions

Short answers on blind flanges and how they get counted.

A solid flange with bolt holes and no bore, used to close off the end of a pipe, valve or nozzle.

The Takeoff Handbook

Reference the Estimating Library

Price your bid before your competitors open the package.

Book a Demo