Field Reference

Steel Base Plate for Industrial Columns: Weights, Anchor Bolts and Takeoff

November 2026By Vini P.K.
steel-base-plate-3dSTEEL COLUMN BASE PLATEBASE PLATEGROUT PADANCHOR RODSW COLUMNCOUNTEDPLATE 14X14X156 LBANCHOR RODS4NUTS + WASHERS8GROUT PAD1

Short Answer

A steel base plate is a flat steel plate welded to the bottom of a column that spreads the column's load onto the concrete foundation. It is held down by anchor bolts cast into the concrete, set level on leveling nuts or shims, and grouted underneath. On a takeoff, each base plate is counted with its size and thickness, its weight, its anchor bolts and its grout.

Sits between
The steel column and the concrete footing
Held down by
Anchor bolts, also called anchor rods
Weight rule
40.84 lb per square foot per inch of thickness
Design guide
AISC Design Guide 1
Field Reference · Structural Steel

Steel Plate Weight Chart by Thickness

Weight of carbon steel plate per square foot, and two common base plate sizes, by thickness.

Thickness (in)Weight (lb/sq ft)12 x 12 Plate (lb)18 x 18 Plate (lb)
1/410.2110.223.0
3/815.3215.334.5
1/220.4220.445.9
5/825.5325.557.4
3/430.6330.668.9
140.8440.891.9
1-1/451.0551.1114.9
1-1/261.2661.3137.8
281.6881.7183.8

Weights use 490 lb per cubic foot for carbon steel and ignore anchor bolt holes. For other sizes, use the metal tonnage calculator.

What Is a Steel Base Plate?

A column base plate is the connection between a steel column and its foundation. The column is welded to the plate in the shop, the plate sits on the concrete with a layer of grout under it, and anchor bolts cast into the footing hold it down. Steel column base plates show up under every building column, pipe rack column and equipment support on an industrial job.

Base plate design sets the plate's size, thickness and anchor bolt pattern from the column load, and AISC (American Institute of Steel Construction) Design Guide 1 is the usual reference. Steel base plates for heavy columns can run 2 inches thick or more, while a unistrut base plate for a strut-channel pipe or conduit support may be a light bolted plate a few inches square.

What Goes With Every Base Plate

ItemWhat It DoesHow It Is Counted
Anchor boltsHold the plate down to the concreteBy diameter, length and grade, usually 4 per plate
Nuts and washersClamp the plate to the anchor boltsTwo nuts and a plate washer per anchor bolt
Leveling nutsSet the plate at the right height before groutingOne per anchor bolt, where the detail shows them
Base plate groutFills the gap between plate and concreteBy volume, or as one grout pad per plate
Embed platesPlates cast into concrete for other connectionsCounted separately, by size and studs

Anchor bolt sizes on building columns commonly run from 3/4 inch to 1-1/2 inch, with larger bolts under heavy industrial equipment. Anchor bolts are often supplied by the steel fabricator but set by the concrete contractor, so check the scope of work for who carries them.

How to Calculate Base Plate Weight

Weight (lb) = width (in) × length (in) ÷ 144 × thickness (in) × 40.84

The 40.84 is the weight of one square foot of carbon steel plate one inch thick. Base plate weight is small next to the columns, but on a pipe rack with hundreds of columns it adds up, and it all goes to the galvanizer by weight.

Worked Example: A 14 x 14 x 1 Inch Base Plate

  1. Area = 14 × 14 ÷ 144 = 1.36 square feet
  2. Weight = 1.36 × 1 × 40.84 = about 56 lb
  3. Add 4 anchor bolts, 8 nuts, 4 plate washers and 4 leveling nuts
  4. Add one grout pad and the shop weld between the column and the plate

Common Mistakes on a Base Plate Takeoff

  • Counting the column and missing its base plate, which is often shown only in a detail
  • Pricing anchor bolts in the steel bid when the concrete contractor carries them, or leaving them out of both
  • Using one base plate size for every column when the schedule lists several
  • Missing leveling nuts, plate washers and grout
  • Leaving base plates out of the galvanizing weight

How The Takeoff AI Handles Base Plates

The Takeoff AI estimates the structural drawings, the specification and the scope of work, and takes off the steel end to end. It counts every column, base plate, anchor bolt and connection, works out the weight, and prices the material takeoff (MTO) and labor takeoff (LTO) into a priced bill of materials (BOM), including galvanizing and hot-dip galvanizing, at your own rates.

Its nesting fits plate parts onto stock plates to cut waste, and it builds a 3D model from the 2D drawings. It is trained on more than 1 million drawing sets and runs at 95% accuracy. 113 estimators say The Takeoff AI is the best structural steel estimating software they have used, and it helps them estimate projects in 3 to 4 hours that once took 40 to 50 hours. See it on the structural steel page.

Before you ask

Frequently Asked Questions

Short answers on steel base plates and how they get counted.

A flat steel plate welded to the bottom of a column that spreads the column's load onto the concrete foundation.

The Takeoff Handbook

Reference the Estimating Library

Price your bid before your competitors open the package.

Book a Demo