Field Reference

Electrical Disconnect Symbol on a Single Line Diagram

November 2026By Vini P.K.
single-line-disconnect-symbolsSINGLE LINE DIAGRAMUTILITYXFMRMAIN BREAKERBUSDS-1MFDS-2MFDS-3MDS-4MSYMBOLS COUNTEDDISCONNECT SWITCH2FUSED DISCONNECT2CIRCUIT BREAKER1TRANSFORMER1MOTOR4DISCONNECTS HIGHLIGHTED ON EACH MOTOR FEEDER

Short Answer

The electrical disconnect symbol shows a manual switch that isolates a circuit, usually drawn on a single line diagram as a short blade set at an angle between two contact points. A fused disconnect adds a fuse below the blade. Estimators count each disconnect by amperage, poles, voltage and enclosure, along with its fuses, conduit and wire.

Drawn as
A blade at an angle between two contacts
Fused version
The same blade with a fuse below it
Found on
Single line diagrams and power plans
Counted by
Amps, poles, voltage and enclosure
Field Reference · Electrical

Single Line Diagram Symbols That Get Confused

The disconnect switch symbol and the symbols most often mistaken for it, how each is drawn and how it is counted.

SymbolHow It Is DrawnWhat It MeansCount As
Disconnect switch (non-fused)A short blade at an angle between two contact pointsA manual switch that isolates the circuitOne disconnect, by amps, poles and enclosure
Fused disconnectThe same blade with a fuse, often a small rectangle, below itA disconnect that also protects the circuitOne disconnect plus a set of fuses
Circuit breakerA small square, or a curved arc on some drawingsAutomatic overcurrent protectionOne breaker, by frame and trip rating
ContactorTwo short parallel lines, with a coil referenceA switch opened and closed by a control signalUsually part of a motor starter
Selector switchA contact with a lever and labeled positions such as hand, off and autoLets an operator pick a modeOne operator device on a control station

Symbol styles vary between engineering firms, so check the legend sheet for the disconnect symbol electrical drawings on that job use. The electrical symbols library covers the common ones.

What Is the Symbol for Disconnect on a Wiring Diagram?

The electrical symbol for disconnect is a switch drawn open: a line, a contact point, a blade angled away from the next contact, and the line carrying on below. On single line diagram symbols sheets, also called one line diagram symbols, it sits between the feeder and the equipment it isolates. The symbol for disconnect switch looks much the same on a schematic, where each pole may be drawn separately.

A fused disconnect symbol adds a fuse below the blade, and some drawings label it as a fusible disconnect symbol or simply FDS. A non-fused disconnect has no fuse and relies on a breaker upstream for protection. Knowing which one is shown matters, because fuses are a separate line on the takeoff.

Disconnect Symbol vs Contactor and Selector Switch

The disconnect symbol gets confused most often with two others. The contactor symbol electrical drawings use is two short parallel lines, operated by a coil rather than by hand. The selector switch symbol shows a lever with marked positions, such as hand, off and auto, and belongs on a control station rather than in the power path.

How to Count Disconnects From a Single Line Diagram

Disconnects = every disconnect symbol on the single line diagram + local disconnects shown on the power plans

The single line diagram shows the main distribution, but local disconnects at motors and equipment are often shown only on the power plans or in equipment schedules. The NEC (National Electrical Code) generally requires a disconnecting means within sight of each motor, so a motor without a disconnect on the drawings is worth a question.

Worked Example: Six Pump Motors

  1. A motor control center feeds 6 pump motors, each with a local fused disconnect
  2. Count 6 fused disconnects, by amps, poles, voltage and NEMA (National Electrical Manufacturers Association) enclosure type
  3. Count 18 fuses for six three-phase disconnects
  4. Count 12 conduit runs: one from the motor control center to each disconnect, and one from each disconnect to its motor, with wire and terminations at each end

Common Mistakes When Counting Disconnects

  • Counting disconnects from the single line diagram only and missing the local ones on the power plans
  • Missing the fuses on a fused disconnect
  • Pricing a standard enclosure where the area classification calls for an explosion-proof or stainless one
  • Confusing a contactor or selector switch with a disconnect
  • Leaving out the conduit and wire on both sides of the disconnect

How The Takeoff AI Handles Electrical Symbols

The Takeoff AI estimates the full electrical and instrumentation (E&I) package, including single line diagrams, power plans, schedules and the specification. It counts every disconnect, breaker, motor, panel and instrument, measures conduit, cable and cable tray, and prices the material takeoff (MTO) and labor takeoff (LTO) into a priced bill of materials (BOM) at your own rates. It also builds a 3D model from the 2D drawings.

It is trained on more than 1.2 million electrical and instrumentation drawings, and every quantity is highlighted on the sheet it came from with an accept or reject option. More than 157 electrical estimators say The Takeoff AI saves them 90% of their time.

Before you ask

Frequently Asked Questions

Short answers on the electrical disconnect symbol and how it gets counted.

A switch drawn open, with a short blade set at an angle between two contact points.

The Takeoff Handbook

Reference the Estimating Library

Price your bid before your competitors open the package.

Book a Demo